The PVI Modular XP Ramp System with Handrail KIT 7 has a clean uncluttered appearance that will fit in most surroundings. All aluminum design has lifetime durability in all kinds of climates. The PVI Modular Ramp System is designed to be freestanding and independent of the existing structure. In most cases this simplifies compliance with local codes and may eliminate the requirement for a permit. The components of the PVI Modular Ramp System are designed to be quickly and easily assembled with simple/common hand tools and set into place without the need for heavy construction equipment. A van, pickup truck, or small trailer is all that is needed to transport the ramp components to the job site.
Please email photos/measurements and SHIP TO address to: Service@AdaptiveLivingStore.com and we will provide quote.
PVI Aluminum Modular XP Ramp Kit 7 includes:
- Two Modular Ramps with Handrails (choose 4', 6', 8' or 10' length)
- One Switchback Platform
- One Turn Platform
- Installation brackets & hardware.
Please reference the Incline Chart to define Rise In Inches for planning of safe ramp slope.
The Adaptive Living Store recommends following ADA Guidelines when installing ramp solutions.
Features:
- Easy to assemble, move, or reconfigure
- Ramp sections are welded in lengths of 3', 4' & 5' and combined to create longer ramp lengths
- Durable and weather resistant
- All aluminum construction
- Little or no maintenance
- 45° and 60° platforms available for those hard to reach landing areas
- ADA handrail extensions, stairs, and gates available
- Standard 36" and custom 42", & 48" Wide ramping available
- Standard 4X4, 4X5, 5X5, 5X6, 5X8, 5X10, & 6X6 platforms available
- Limited Lifetime Warranty
- Made in the USA
Specifications:
- Width: 36" Usable
- Length: Variable - 4’ minimum
- Load Capacity: 100 lbs. per square foot
- Slope: Adjustable – 1:12 Recommended
- Floor: Slip resistant grooved aluminum
- Ramp Edge Protection: 4” Curb - Meets ADA Standards
- Handrails: Double 1-1/2” bar – Standard Height 34"–38"
LAYOUT CONSIDERATIONS:SLOPES: The ADA recommends a slope of 1on12 when possible. However, when space is limited or other considerations require a steeper ramp, the PVI Modular Ramp System will accommodate slopes up to 2on12. When selecting the slope of the ramp the capabilities and safety of the users and their equipment must be considered.
HANDRAIL: ADA requires handrail on any system with a rise of 6” or more. All PVI Modular Ramp Systems require handrail. Ramps and landings will not be sold without handrail for safety reasons as well as the overall design of the ramp system.
RAMP CONFIGURATIONS: The usable width of the ramp is 36” with the overall width of the ramp being 42”. The length of the individual ramp segments are as follows: 2', 3’, 4’, & 5’. The segments are used to make lengths from 4’ and longer in 1’ increments.
RAMP AND LANDING ASSEMBLY: Complete detailed assembly instructions are included with each PVI Modular Ramp System. NOTE: DURING ASSEMBLY DO NOT TIGHTEN HARDWARE ALL THE WAY UNTIL ASSEMBLY IS COMPLETE.
FOOTING AND ANCHORING: The PVI Modular Ramp System is designed to be a freestanding, independent structure that does not have to be permanently attached to the building it serves. Each supporting leg is independently adjustable to allow for varying ground conditions. Adjustments due to settling or heaving can be made with a ratchet. Landings must have a minimum of one leg anchored on each of the two opposite sides. Each freestanding ramp must be anchored at the upper and lower end. Anchoring may consist of lag screws or bolts into existing concrete, precast pads, patio pavers or poured in place.
See PVI Modular Ramp System Quick Start Instructions here.